Skip to main content

Posts

Showing posts with the label Plaoalto Firewall

How to enable logging in Palo Alto Networks Firewall?

How to enable logging in Palo Alto Networks Firewall? When it comes to live troubleshooting or to ensure certain traffic is either blocked or allowed one relies heavily on logs, Palo Alto Network Firewalls does provides very good logging options and fields. Its quite easy to read them and understands them. By default when some one creates any security policy Palo Alto Networks Firewall logs the details at the end of the session. So one does not need to enable logging, if he/she wants to monitor session since it started then they have enable the it. One can enable logging, directly from the security policy he/she creates as shown below

What are the modes in which interfaces on Palo Alto can be configured?

What are the modes in which interfaces on Palo Alto can be configured? When configuring the Ethernet ports on your firewall, you can choose from virtual wire, Layer 2, or Layer 3 interface deployments. In addition, to allow you to integrate into a variety of network segments, you can configure different types of interfaces on different ports. The following sections provide basic information on each type of deployment. -Virtual Wire Deployments -Layer 2 Deployments -Layer 3 Deployments Virtual Wire Deployments In a virtual wire deployment, the firewall is installed transparently on a network segment by binding two ports together. By using a virtual wire, you can install the firewall in any network environment without reconfiguring adjacent devices. If necessary, a virtual wire can block or allow traffic based on the virtual LAN (VLAN) tag values. You can also create multiple subinterfaces and classify traffic according to an IP Address (...

Policy Based Forwarding on a Palo Alto with different Virtual Routers

Policy Based Forwarding on a Palo Alto with different Virtual Routers This guide is a little bit different to my other Policy Based Forwarding blog post because it uses different virtual routers for both ISP connections . This is quite common to have a distinct default route for both providers. So, in order to route certain traffic, e.g., http/https, to another ISP connection, policy based forwarding is used. There are two documents from Palo Alto that give advises how to configure PBF. I am using a PA-200 with PAN-OS 7.0.1. My lab is the following: (Note that, unlike Juniper ScreenOS, a zone is not tied to a virtual router. You actually can merge interfaces on different vrouters into the same zone. However, I prefer to configure an extra zone for each ISP to keep my security policies clearly separated.) These are the configuration steps. See the descriptions under the screenshots for details: Two virtual routers: d...

Palo Alto Remote Access VPN for Android

Palo Alto Remote Access VPN for Android For a basic remote access VPN connection to a Palo Alto Networks firewall (called “GlobalProtect”), the built-in VPN feature from Android can be used instead of the GlobalProtect app from Palo Alto itself. If the additional features such as HIP profiling are not needed, this variant fits perfectly. I am showing a few screenshots and logs from the Android smartphone as well as from the Palo Alto to show the differences. This post is very similar to the post about the iPhone . I am running a PA-200 with PAN-OS version 7.0.3 . The phone is a Samsung Galaxy S4 Mini with Android version 4.4.2 . The GlobalProtect app from Palo Alto works without any problems if a correct Portal and Gateway are already configured. In order to use the native “IPSec Xauth PSK” on Android, the “X-Auth Support” must be enabled on the GlobalProtect Gateway, such as shown here in my post about the Linux vpnc client . Glo...

Where to terminate Site-to-Site VPN Tunnels?

Where to terminate Site-to-Site VPN Tunnels? When using a multilayer firewall design it is not directly clear on which of these firewalls remote site-to-site VPNs should terminate. What must be considered in such scenarios? Differentiate between partners and own remote offices? Or between static and dynamic peer IPs? What about the default routes on the remote sites? Following is a discussion about different approaches and some best practices. Since not all concepts work with all firewall vendors, the following strategies are separated by common firewalls, i.e., Cisco ASA, Fortinet FortiGate, Juniper ScreenOS, Palo Alto. (This is one of many VPN tutorials on my blog. Have a look at this full list .) Of course, if there is only a single firewall in place, this discussion is not necessary at all . All VPN tunnels must solely terminate on this single firewall. You’re done. But most customers have at least a two-firewall strategy whi...

Palo Alto Software Download Failure

Palo Alto Software Download Failure I had an error on my PA-200 with PAN-OS 7.0.5 while trying to download a new firmware version. “Error: There is not enough free disk space to complete the desired operation. […]”. Even the tips to delete older software, dynamic updates, etc., and to use the “set max-num-images count” command did not lead to a successful download. Finally, the TAC support could solve the problem via root access to the Palo Alto firewall and by manually moving data files… This was the disk space on the firewall before the TAC support corrected it (note the 5th line with 92 % usage): 1 2 3 4 5 6 7 8 weberjoh @ fd - wv - fw02 > show system disk - space   Filesystem             Size   Used Avail Use % Mounted on / dev / sda3         ...

Palo Alto VPN Speedtests

Palo Alto VPN Speedtests Once more some throughput tests, this time the Palo Alto Networks firewalls site-to-site IPsec VPN . Similar to my VPN speedtests for the FortiGate firewall , I set up a small lab with two PA-200 firewalls and tested the bandwidth of different IPsec phase 2 algorithms. Compared to the official data sheet information from Palo Alto that state an IPsec VPN throughput of 50 Mbps, the results are really astonishing. (This is one of many VPN tutorials on my blog. Have a look at this full list .).) Lab My lab consists of two PA-200 firewalls with PAN-OS 7.1.1 installed. They were plugged into a simple layer 2 switch. The two notebooks were booted with Knoppix 7.6.1 and used Iperf version 2.0.5 . I first tested the throughput with only routing and then built the VPN. After every test I changed the phase 2 parameters. The Iperf tests ran in both directions. Here are some configuration screenshots: ...