FortiGate: Upgrading the firmware via CLI

To use the following procedure, you must have a TFTP or FTP server that FortiDB can connect to. You must also log in using the “admin” administrator account.

Start the FTP or TFTP server.
Copy the new firmware image file to the FTP or TFTP server.
Log into the CLI.
Verify that FortiDB can connect to the FTP or TFTP server. For example, if the IP address of the TFTP server is 192.168.1.168, enter the CLI command:
```
execute ping 192.168.1.168
```
Enter the following command to copy the firmware image from the TFTP server to FortiDB:
```
execute restore image ftp  
execute restore image tftp  
```
Where is the name and location of the firmware image file and or is the IP address of the FTP or TFTP server. For example, if the firmware image file name is image.out and the IP address of the FTP or TFTP server is 192.168.1.168, enter:
```
execute restore image tftp image.out 192.168.1.168
```
FortiDB responds with the message:
```
This operation will replace the current firmware version!
Do you want to continue? (y/n)
```
Type y. FortiDB downloads the firmware image file, upgrades to the new firmware version, and restarts. This process takes a few minutes.
Reconnect to the CLI.
To confirm the new firmware image is successfully installed, enter:
```
get system status
```

Comments

Checkpoint firewall common commands part 2

Checkpoint firewall common commands part 2 For basic firewall informaton gathering: fgate stat -Status and statistics of Flood-Gate-1. fwaccel <stat|stats|conns> – View status, statistics or connection table of SecureXL. fw getifs -Show list of configured interfaces with IP and netmask. cpstat <app_flag> [-f flavour] -View OS, HW and CP application status. Issue cpstat without any options to see all possible application flags <app_flag> and corresponding flavours. Examples: cpstat fw -f policy – verbose policy info cpstat os -f cpu – CPU utilization statistics cpinfo -y all -List all installed patches and hotfixes. cpd_sched_config print -Show task scheduled with CPD scheduler. enabled_blades -View enabled software blades avsu_client [-app <app>] , get_version <app> -Get signature version and status of content security .Without the -app option “Anti Virus” is used. show co...

Unable to Connect to Server Checkpoint R80

Unable to Connect to Server Checkpoint R80 Unable to Connect to Server A connection to the management server will fail if: A firewall between SmartConsole and the management server blocks Port 19009 - port 19009 is used for a new R80 service. Allow traffic on this port for all clients and management servers. No GUI clients are assigned - Open the Gaia Portal. If the First Time Configuration Wizard opens, complete it. If the First Time Configuration Wizard has already run, open User Management > GUI Clients and add a client. When using Multi-Domain Security Management, connect SmartConsole to the Multi-Domain Server and make sure the domains have GUI clients assigned to them. The required processes are not reachable - Make sure the computer with SmartConsole installed can reach the IP address of the management server, and that these server processes are up and running: cpm fwm Operation time out – Your connection ...

Configuring Proxy ARP for Manual NAT

Configuring Proxy ARP for Manual NAT Symptoms After creating a Manual Static NAT rule, Security Gateway does not answer the ARP Requests for the Static NATed IP address that was configured in the Manual NAT rule. Security Gateway replies to ARP requests with a wrong MAC address, mostly for the NAT traffic. Introduction Let us consider the following scenario: Two networks ( Network_A and Network_B ) are separated by a Security Gateway (single Security Gateway or ClusterXL). On each network, there is a host ( Host_A on Network_A , Host_B on Network_B ). Let us assume, that Network_A represents the Internal network, and Network_B represents the External network. According to the existing standards, when Host_B needs to send data to Host_A , an ARP Request for the MAC address of Host_A will be sent by Host_B to Network...

Secure IT

Search This Blog